特色行業廢氣處理介紹化工廠廢氣屬于多元復雜化廢氣，廢氣中含有無機廢氣和有機廢氣，廢氣中一般會體現出強酸、強堿、惡臭、粘附、高溫，高濕等多種特性，此種工況下要用一臺單獨設備處理完廢氣不現實，通過多年的經驗，我公司現設計處理化工廢氣一般采用組合式廢氣處理裝置，把有機廢氣裝置和無機廢氣裝置聯合在一起，因此要在光氧廢氣處理裝置前設置洗滌塔，作為預處理器，從而確保由原配套風機抽風引入的廢氣中所含塵雜、無機廢氣、強酸、強堿在進入光氧廢氣處理裝置時得到有效的攔截過濾。把通過初步預處理的廢氣送入光氧廢氣處理裝置后采用風機送出。注：含有易燃易爆廢氣，電器部分必須做電器防爆處理。
工業凈化油漆味專用設備！工業凈化油漆味專用設備是通過利用高性能活性炭吸附劑固體本身的表面作用力，能對苯、醇、酮、酯、汽油類等有機溶劑的廢氣吸附，更適用于大風量低濃度的有機廢氣治理，它能有效地凈化環境、消除污染、并能回收有機溶劑，降低生產成本?！ ?、純物理的吸附原理，維護保養簡單方便 2、設備表面采用噴塑處理， 3、獨特的產品結構設計，，使得凈化率可達90%以上; 4、無二次污染，真正環保產品 工業凈化油漆味專用設備！工業凈化油漆味專用設備是通過利用高性能活性炭吸附劑固體本身的表面作用力，能對苯、醇、酮、酯、汽油類等有機溶劑的廢氣吸附，更適用于大風量低濃度的有機廢氣治理，它能有效地凈化環境、消除污染、并能回收有機溶劑，降低生產成本?！ ?、純物理的吸附原理，維護保養簡單方便 2、設備表面采用噴塑處理， 3、獨特的產品結構設計，，使得凈化率可達90%以上; 4、無二次污染，真正環保產品適用范圍： 油漆味專用設備是一種內裝填粗石英砂墊層及優質活性炭?；钚蕴窟^濾器一般應用于空調通風系統異味及，有害氣體(如苯、甲醛、氨氣等)的吸附脫除溶劑的回收.功能：廣泛適用于食品、醫藥、電子、化工、工業廢水等行業。味專用設備?！ ?
活性炭臭氣吸附裝置技術說明一、 活性炭吸附塔概述活性炭，是一種高效率經濟實用型有機廢氣的凈化與治理裝置；該設備是凈化較高濃度有機廢氣和噴漆廢氣的吸附設備，是利用活性炭本身高強度的吸附力，對苯、醇、酮、酯、汽油類等有機溶劑的廢氣有很好的吸附作用?？偨Y國內外同類產品的生產經驗，改進設計制造，表面平整度更好，結構強度更，吸附能力更強的活性炭本公司生產多種規格的活性碳吸附塔，根據處理氣體污染因子的不同而設計吸附時間，再根據處理廢氣量的大小確定吸附面積，每一是否含有油霧、粉塵等相關參數，在廢氣設備進口部分內置或增設冷卻器、過濾器等預處理裝置或功能段。確保高效狀態下運行。二、性能特點1、吸附效率高,能力強；2、設備構造緊湊，運轉成本低；3、能夠同時處理多種混合有機廢氣；4、采用自動化控制運轉設計5室內外皆可使用。三、適用范圍。主要應用領域包括：電子元件生產、電池（電瓶）生產、酸洗作業車間、實驗室排風、產等行業廢氣凈化，其中＊適用于噴漆廢氣處理凈化。純活性炭吸附處理有機廢氣是利用活性炭微孔能吸收有機性物質的特性，經吸附凈化后的氣體達標直接排空。其實質是一個物理的吸附濃縮的過程。
詳細描述一、產品概述 袋式除塵器是一種干式濾塵裝置。濾料使用一段時間后，由于篩濾、碰撞、滯留、擴散、靜電等效應，濾袋表面積聚了一層粉塵，這層粉塵稱為初層，在此以后的運動過程中，初層成了濾料的主要過濾層，依靠初層的作用，網孔較大的濾料也能獲得較高的過濾效率。隨著粉塵在濾料表面的積聚，除塵器的效率和阻力都相應的增加，當濾料兩側的壓力差很大時，會把有些已附著在濾料上的細小塵粒擠壓過去，使除塵器效率下降。另外，除塵器的阻力過高會使除塵系統的風量顯著下降。因此，除塵器的阻力達到一定數值后，要及時清灰。清灰時不能破壞初層，以免效率下降。二、應用范圍 染料、制藥、塑膠和印刷廠、涂料廠、食品加工、面粉、電子行業、木材加工等領域的液固分離及微細物料回收治理和凈化收集。三、工作原理 當含塵氣體由進風口進入除塵器，首先碰到進出風口中間的斜板及擋板，氣流便轉向進入灰斗，同時氣流速度放慢，在慣性作用下，氣體中粗顆粒粉塵直接沉降到灰斗，起預收塵的作用，氣流隨后折而向上通過內部裝有金屬骨架的濾袋粉塵被捕集在濾袋的外表面，凈化后的氣體進入濾袋室下部清潔室，匯集到出風口排出。含塵氣體通過濾袋凈化的過程中，隨著時間的增加而積附在濾袋上的粉塵越來越多，濾袋阻力增加，致使處理風量逐漸減少,必須對濾袋進行清灰，使積附在濾袋表面的粉塵脫落，濾袋得到再生。清下粉塵落入灰斗，經排灰系統排出機體。由此使積附在濾袋上的粉塵周期地脈沖噴吹清除，使凈化氣體正常通過，保證除塵系統正常工作。四、產品構造 袋式除塵器本體結構主要由上部箱體、中部箱體、下部箱體（灰斗）、清灰系統和排灰機構等部分組成。袋式除塵器性能的好壞，除了正確選擇濾袋材料外，清灰系統對袋式除塵器起著決定性的作用。為此，清灰方法是區分袋式除塵器的特性之一，也是袋式除塵器運行中重要的一環。One、 product overviewBag type dust collector is a kind of dry dust filtering device. Filter used for a period of time, due to the sifting, collision, retention, diffusion, electrostatic and other effects, the bag surface of a layer of dust, this layer of dust known as the first layer, in which the future course of the movement, became the first layer mainly filter layer filter material, rely on the role of the early levels, larger mesh the filter can get a higher filtration efficiency. As the dust on the filter surface accumulation, efficiency and resistance of the dust collector are increased correspondingly, when the filter pressure difference on both sides is large, will put some has attached to small dust particles in the filter on the squeeze in the past, so that the precipitator efficiency decline. In addition, the resistance of the dust collector is too high will make the dust removal system of the wind dropped significantly.Therefore, the dust collector resistance reaches a certain value, to timely cleaning. Cleaning can not be destroyed when the first layer, to avoid reduced efficiency.Two、 the scope of applicationSolid separation we dye, pharmaceutical, plastic and printing factory, paint factory, food processing,flour, electronic industry, wood processing and other fields of liquid and fine material recoverytreatment and purification collection.Three、the principle of workWhen the dust contained gas from the inlet into the dust, met at the air inlet and outlet of theinclined plate and the middle baffle, flow turned into ash hopper, while the air flow speed slow down,under the inertia effect, gas dust settling into the hopper of coarse particles directly, since the role of airflow with dust in advance, after folding to filter bag dust through with internal metal skeletontrapped in the outer surface of the filter bag, purified gas into the filter bag chamber bottom clean room, pool to the discharge outlet. The process of dust containing gas through the filter bagcleaning, along with the increase of time more and more dust deposition in the filter bag, bagresistance increases, causing the air handling gradually reduced, must carry on the cleaning of the bag, so that the product of shedding in the filter bag dust filter bag surface, regeneration. Clear the dust falls into the bucket, the ash discharge system and discharged out of the machine body.Thereby the deposition in the filter bag dust cycle of the pulse jet cleaned, the purification of gaspassed normally, ensure the normal work of the dust removal system.Four,、product structureBody structure of bag type dust collector is mainly composed of an upper box body, a box body, the middle lower case (Hui Dou), the ash cleaning system and ash body parts. Device performance of bag type dust collector is good or bad, in addition to the correct choice of bag material, ash cleaning system plays a decisive role in the bag type dust remover. Therefore, the ash cleaningmethod is one of the characteristics that distinguish bag type dust collector, an important link in the operation is also a bag type dust collector.相關產品
詳細描述一、產品概述 袋式除塵器是一種干式濾塵裝置。濾料使用一段時間后，由于篩濾、碰撞、滯留、擴散、靜電等效應，濾袋表面積聚了一層粉塵，這層粉塵稱為初層，在此以后的運動過程中，初層成了濾料的主要過濾層，依靠初層的作用，網孔較大的濾料也能獲得較高的過濾效率。隨著粉塵在濾料表面的積聚，除塵器的效率和阻力都相應的增加，當濾料兩側的壓力差很大時，會把有些已附著在濾料上的細小塵粒擠壓過去，使除塵器效率下降。另外，除塵器的阻力過高會使除塵系統的風量顯著下降。因此，除塵器的阻力達到一定數值后，要及時清灰。清灰時不能破壞初層，以免效率下降。二、應用范圍 染料、制藥、塑膠和印刷廠、涂料廠、食品加工、面粉、電子行業、木材加工等領域的液固分離及微細物料回收治理和凈化收集。三、工作原理 當含塵氣體由進風口進入除塵器，首先碰到進出風口中間的斜板及擋板，氣流便轉向進入灰斗，同時氣流速度放慢，在慣性作用下，氣體中粗顆粒粉塵直接沉降到灰斗，起預收塵的作用，氣流隨后折而向上通過內部裝有金屬骨架的濾袋粉塵被捕集在濾袋的外表面，凈化后的氣體進入濾袋室下部清潔室，匯集到出風口排出。含塵氣體通過濾袋凈化的過程中，隨著時間的增加而積附在濾袋上的粉塵越來越多，濾袋阻力增加，致使處理風量逐漸減少,必須對濾袋進行清灰，使積附在濾袋表面的粉塵脫落，濾袋得到再生。清下粉塵落入灰斗，經排灰系統排出機體。由此使積附在濾袋上的粉塵周期地脈沖噴吹清除，使凈化氣體正常通過，保證除塵系統正常工作。四、產品構造 袋式除塵器本體結構主要由上部箱體、中部箱體、下部箱體（灰斗）、清灰系統和排灰機構等部分組成。袋式除塵器性能的好壞，除了正確選擇濾袋材料外，清灰系統對袋式除塵器起著決定性的作用。為此，清灰方法是區分袋式除塵器的特性之一，也是袋式除塵器運行中重要的一環。One、 product overviewBag type dust collector is a kind of dry dust filtering device. Filter used for a period of time, due to the sifting, collision, retention, diffusion, electrostatic and other effects, the bag surface of a layer of dust, this layer of dust known as the first layer, in which the future course of the movement, became the first layer mainly filter layer filter material, rely on the role of the early levels, larger mesh the filter can get a higher filtration efficiency. As the dust on the filter surface accumulation, efficiency and resistance of the dust collector are increased correspondingly, when the filter pressure difference on both sides is large, will put some has attached to small dust particles in the filter on the squeeze in the past, so that the precipitator efficiency decline. In addition, the resistance of the dust collector is too high will make the dust removal system of the wind dropped significantly.Therefore, the dust collector resistance reaches a certain value, to timely cleaning. Cleaning can not be destroyed when the first layer, to avoid reduced efficiency.Two、 the scope of applicationSolid separation we dye, pharmaceutical, plastic and printing factory, paint factory, food processing,flour, electronic industry, wood processing and other fields of liquid and fine material recoverytreatment and purification collection.Three、the principle of workWhen the dust contained gas from the inlet into the dust, met at the air inlet and outlet of theinclined plate and the middle baffle, flow turned into ash hopper, while the air flow speed slow down,under the inertia effect, gas dust settling into the hopper of coarse particles directly, since the role of airflow with dust in advance, after folding to filter bag dust through with internal metal skeletontrapped in the outer surface of the filter bag, purified gas into the filter bag chamber bottom clean room, pool to the discharge outlet. The process of dust containing gas through the filter bagcleaning, along with the increase of time more and more dust deposition in the filter bag, bagresistance increases, causing the air handling gradually reduced, must carry on the cleaning of the bag, so that the product of shedding in the filter bag dust filter bag surface, regeneration. Clear the dust falls into the bucket, the ash discharge system and discharged out of the machine body.Thereby the deposition in the filter bag dust cycle of the pulse jet cleaned, the purification of gaspassed normally, ensure the normal work of the dust removal system.Four,、product structureBody structure of bag type dust collector is mainly composed of an upper box body, a box body, the middle lower case (Hui Dou), the ash cleaning system and ash body parts. Device performance of bag type dust collector is good or bad, in addition to the correct choice of bag material, ash cleaning system plays a decisive role in the bag type dust remover. Therefore, the ash cleaningmethod is one of the characteristics that distinguish bag type dust collector, an important link in the operation is also a bag type dust collector.相關產品
詳細描述一、產品概述 袋式除塵器是一種干式濾塵裝置。濾料使用一段時間后，由于篩濾、碰撞、滯留、擴散、靜電等效應，濾袋表面積聚了一層粉塵，這層粉塵稱為初層，在此以后的運動過程中，初層成了濾料的主要過濾層，依靠初層的作用，網孔較大的濾料也能獲得較高的過濾效率。隨著粉塵在濾料表面的積聚，除塵器的效率和阻力都相應的增加，當濾料兩側的壓力差很大時，會把有些已附著在濾料上的細小塵粒擠壓過去，使除塵器效率下降。另外，除塵器的阻力過高會使除塵系統的風量顯著下降。因此，除塵器的阻力達到一定數值后，要及時清灰。清灰時不能破壞初層，以免效率下降。二、應用范圍 染料、制藥、塑膠和印刷廠、涂料廠、食品加工、面粉、電子行業、木材加工等領域的液固分離及微細物料回收治理和凈化收集。三、工作原理 當含塵氣體由進風口進入除塵器，首先碰到進出風口中間的斜板及擋板，氣流便轉向進入灰斗，同時氣流速度放慢，在慣性作用下，氣體中粗顆粒粉塵直接沉降到灰斗，起預收塵的作用，氣流隨后折而向上通過內部裝有金屬骨架的濾袋粉塵被捕集在濾袋的外表面，凈化后的氣體進入濾袋室下部清潔室，匯集到出風口排出。含塵氣體通過濾袋凈化的過程中，隨著時間的增加而積附在濾袋上的粉塵越來越多，濾袋阻力增加，致使處理風量逐漸減少,必須對濾袋進行清灰，使積附在濾袋表面的粉塵脫落，濾袋得到再生。清下粉塵落入灰斗，經排灰系統排出機體。由此使積附在濾袋上的粉塵周期地脈沖噴吹清除，使凈化氣體正常通過，保證除塵系統正常工作。四、產品構造 袋式除塵器本體結構主要由上部箱體、中部箱體、下部箱體（灰斗）、清灰系統和排灰機構等部分組成。袋式除塵器性能的好壞，除了正確選擇濾袋材料外，清灰系統對袋式除塵器起著決定性的作用。為此，清灰方法是區分袋式除塵器的特性之一，也是袋式除塵器運行中重要的一環。One、 product overviewBag type dust collector is a kind of dry dust filtering device. Filter used for a period of time, due to the sifting, collision, retention, diffusion, electrostatic and other effects, the bag surface of a layer of dust, this layer of dust known as the first layer, in which the future course of the movement, became the first layer mainly filter layer filter material, rely on the role of the early levels, larger mesh the filter can get a higher filtration efficiency. As the dust on the filter surface accumulation, efficiency and resistance of the dust collector are increased correspondingly, when the filter pressure difference on both sides is large, will put some has attached to small dust particles in the filter on the squeeze in the past, so that the precipitator efficiency decline. In addition, the resistance of the dust collector is too high will make the dust removal system of the wind dropped significantly.Therefore, the dust collector resistance reaches a certain value, to timely cleaning. Cleaning can not be destroyed when the first layer, to avoid reduced efficiency.Two、 the scope of applicationSolid separation we dye, pharmaceutical, plastic and printing factory, paint factory, food processing,flour, electronic industry, wood processing and other fields of liquid and fine material recoverytreatment and purification collection.Three、the principle of workWhen the dust contained gas from the inlet into the dust, met at the air inlet and outlet of theinclined plate and the middle baffle, flow turned into ash hopper, while the air flow speed slow down,under the inertia effect, gas dust settling into the hopper of coarse particles directly, since the role of airflow with dust in advance, after folding to filter bag dust through with internal metal skeletontrapped in the outer surface of the filter bag, purified gas into the filter bag chamber bottom clean room, pool to the discharge outlet. The process of dust containing gas through the filter bagcleaning, along with the increase of time more and more dust deposition in the filter bag, bagresistance increases, causing the air handling gradually reduced, must carry on the cleaning of the bag, so that the product of shedding in the filter bag dust filter bag surface, regeneration. Clear the dust falls into the bucket, the ash discharge system and discharged out of the machine body.Thereby the deposition in the filter bag dust cycle of the pulse jet cleaned, the purification of gaspassed normally, ensure the normal work of the dust removal system.Four,、product structureBody structure of bag type dust collector is mainly composed of an upper box body, a box body, the middle lower case (Hui Dou), the ash cleaning system and ash body parts. Device performance of bag type dust collector is good or bad, in addition to the correct choice of bag material, ash cleaning system plays a decisive role in the bag type dust remover. Therefore, the ash cleaningmethod is one of the characteristics that distinguish bag type dust collector, an important link in the operation is also a bag type dust collector.相關產品
現以獲得新型產品＊＊證書數項、發明＊＊水霧靜電處理設備，可以用在工業處理廢氣、除塵、除味，油煙凈化環保領域系列產品采用了納米和離子技術，主要對車床、金屬加工、焊接、廚房、燒烤等，所含成分如脂肪酸、甲烷經、脂完香等有害的氣體進行處理。餐飲業及食品加工業在生產過程中會產生大量的油煙以及一氧化碳、二氧化硫、碳氫化合物等對人體有害的物質。其中3、4-苯并芘為強致癌物油煙經過凈化器，在高壓等離子電場的作用下，將微小的油顆粒與氣體進行電離荷電，帶電的微小離子（油顆粒）被吸附單元所收集，并流入和沉積到凈化器的儲油箱內，煙塵內的有害氣體，被電場內所產生的臭氧所殺菌，并去除了異味，有害氣體被除掉，潔凈的空氣經出風口排出，達標排放。。其中水霧靜電處理設備。復合式油煙凈化器設備，在2008年已獲得中國環境保護產品認證證書。4
產品描述“還春牌”靜電復合式油霧凈化器設備具有過載保護、缺相保護、漏電保護等功能。高壓電源具有電場打火自動斷電保護功能。設備運行穩定、易操作。二、產品用途適用于真空泵CNC數控車床、清洗機、外圓、平面磨床、滾齒、銑床和插齒機床、真空泵、噴霧試驗室、電火花加工、數控加工中心等工作場所產生的油霧汽體進行凈化器處理和儲存的處理。三、工作原理A、吸入和霧狀物和粉塵進入油霧過濾器首先與慣性碰撞板下撞后 落下，由一次過濾器將大顆粒的霧狀物除去。B、進入二、三次過濾器的小顆粒霧裝物在葉輪的作用下粗?；?，提高下一步濾網的過濾效果。C、三次過濾網為**濾網，能較好的濾去細小的油霧。四、設備好處機床油霧凈化器能將機床切削時所霧化的那部分乳化劑回收再利用，降低其損耗。具體的回收效益數據，要看機床產生霧狀物的程度，一般來說，霧狀物的濃度越高，回收效益越好。油霧直接排放在空調車間內，會降低并損害空調能效，大幅增加空調使用費用；如果將油霧排向室外，不僅會破壞環境（影響企業的社會形象，還又可能被環保部門處罰），而且有可能制造火災隱患，導致財產的意外損失等等；
31011702006117